新聞中心
新聞資訊
聯系我們
山東途暢路橋工程有限公司
聯系人：石總
電話：18264104888
地址：山東省濟南市槐蔭區經一路273號群盛華城
冷再生機"減速機與轉子罩殼"的更換與保養
來源：http://www.kqj188.com/ 日期：2023-04-03 發布人：
一、減速機部分
1、 Reducer part
目前冷再生機配置的是美國原裝進口減速機，是動力傳輸非常重要的部件，對再生機的整體性能起著舉足輕重的作用，它內置在轉子內，作用是減小轉速，增加扭矩。
Currently, the cold regeneration machine is equipped with a reducer imported from the United States, which is a very important component for power transmission and plays a crucial role in the overall performance of the regeneration machine. It is built into the rotor to reduce rotational speed and increase torque.
減速機
Reducer
減速機的保養建議由專門人員操作或指導，首次保養周期是500小時，之后保養周期是1000小時。
The maintenance of the gear unit must be operated or guided by specialized personnel. The first maintenance interval is 500 hours, and the subsequent maintenance interval is 1000 hours.
減速機蓋
Gear unit cover
冷再生機租賃認為其減速機在使用時溫度非常高，后蓋為‘o'型圈密封，容易滲漏；減速機的油封容易被再生料里的鐵絲等堅硬物破壞造成滲油。
The cold regeneration machine rental believes that the temperature of its reducer is very high when it is used, and the rear cover is sealed with an 'o' ring, which is prone to leakage; The oil seal of the reducer is easily damaged by hard objects such as iron wires in the recycled material, causing oil leakage.
二、轉子及罩殼部分
2、 Rotor and casing part
（1）施工過程中注意觀察刀頭磨損情況，發現松動、脫落、折損等情況應及時處理和更換。否則容易造成刀座的磨損，刀座的更換比較麻煩，需要?dú)飧?、電焊等工具，有時工地條件不具備，或焊接水平達不到，直接影響使用，可更換的刀座雖說方便，但會增加使用成本。
(1) During the construction process, pay attention to observing the wear of the cutting head, and promptly handle and replace any loose, detached, or damaged situations. Otherwise, it is easy to cause wear of the knife holder, and the replacement of the knife holder is relatively troublesome, requiring tools such as gas cutting and electric welding. Sometimes the site conditions are not available or the welding level cannot be reached, which directly affects the use. Although replaceable knife holders are convenient, they will increase the use cost.
（2）更換刀頭時可用刀頭攻擊器將舊刀頭敲出，新刀頭用鐵錘敲入刀座孔內即可。焊接刀座時注意焊接角度，否則會導致再生層深淺不一，造成刀具提前磨損等情況，從而會增加發動機負荷，造成不必要的動力輸出。
(2) When replacing the cutter head, use a cutter head attacker to knock out the old cutter head, and use a hammer to knock the new cutter head into the cutter holder hole. Pay attention to the welding angle when welding the cutter holder, otherwise the depth of the regeneration layer may vary, resulting in premature wear of the cutter, and other situations, which may increase engine load and cause unnecessary power output.
（3）銑刨轉子、銑刨轉子罩殼等工作裝置，每天施工結束后應進行清洗，這樣做可以避免以下情況的發生：
(3) Working devices such as milling rotors and milling rotor casings should be cleaned after construction every day to avoid the following situations:
①罩殼上的水噴孔堵塞，次日工作時水分不均;
① The water spray hole on the cover is blocked, resulting in uneven water content during the next day's work;
②再生料粘附在銑刨轉子上出色難清理掉，影響拌合效果;
② The adhesion of recycled materials to the milling rotor is extremely difficult to remove, affecting the mixing effect;
③再生料粘附在刀頭、刀座上，導致更換困難;
③ The recycled material adheres to the cutter head and cutter seat, resulting in difficulty in replacement;
（4）滑靴的保養。對已經磨損的滑靴部分進行補焊，螺紋處應涂抹黃油防銹。更多相關事項就來我們網站http://www.kqj188.com咨詢了解吧！
(4) Maintenance of sliding shoes. Repair welding shall be carried out on the worn sliding shoes, and the threads shall be coated with butter to prevent rust. For more related matters, please visit our website http://www.kqj188.com Consult and understand!
推薦閱讀/ Recommended reading
- 水泥撒布車出租：撒灰車常見故障排除 2026-08-05
- 冷再生拌合機節能降耗技巧有哪些？ 2026-08-05
- 水泥撒布車出租避坑指南先注意這個5點 2026-07-31
- 撒布精度±5%是怎么做到的？ 2026-07-29
撒灰車開啟道路建設新篇章
[2026-08-07]
在當前的交通建設領域，創新技術的應用正不斷推動著行業的進步與發展。其中，撒灰車作為一種新型工程車輛，憑借其便捷的特點，在公路、鐵路、機場道路建設等領域展現出了強大的應用潛力。In...
